Reproduction of the original E50 engine housing with 4 bearings and kick starter for your Puch moped / moped.
The dimensions correspond to the original housing. This means that all add-on parts such as rods, end plates, crankshafts or cylinders can be used.
As with the original, a cylinder and pinion lock has been installed, which must be removed when fitting tuning parts.
The housing parts are numbered. The engine number can be stamped in by the owner if required.
Threaded stud bolt: M6x1 mm
Matching add-on parts and a racing gear for your Puch Maxi can be found in the accessories section.
Branded product from the manufacturer AKOA.
Details
| Manufacturer | AKOA |
| Material | Aluminum |
Suitable for the following models
| Puch | E50 |
Accessories & related products
GPO gasket set | Puch E50
Manufacturer: GPO · Material: Aluminum · Material: Fiber · Material: Sealing carton · Material: Sealing paper · Number of components: 7 pcs · Hole spacing inlet: 32 - 38 mm · Ø outlet inside: 19.9 mm · Hole pattern [mm]: 44 x 44 · Hole spacing outlet: 42 mm · Area of application: Standard · Decompressor: Yes
EUR 12.10
swiing® revival stud bolt set M6 x 106 mm | Puch
Manufacturer: swiing® revival parts · Material: Steel · Surface: galvanized (blue) · Diameter: 5.9 mm · Drive: External hexagon · Total length: 106 mm · Thread length: 13 mm · Thread length: 18.5 mm · Thread type: M6x1 (standard thread) · Width across flats SW: 10 mm · Alternative version of the Puch OEM number: 360.1.10.034.1
EUR 9.00
swiing® revival crankshaft standard with mounted bearings (version 2.0) | Puch E50
Manufacturer: swiing® revival parts · Material: Steel · Cheek type: standard · Crankshaft stroke: 43 mm · Connecting rod length center-center: 90 mm · Thread type: MF10x1 (fine pitch thread) · Ø piston pin (B): 12 mm · Total length of crankpin on clutch side: 74 mm · Total length crankpin ignition side: 66 mm · Ø crank webs: 69.9 mm · Ø Connecting rod eye: 15 mm · Ø Bearing seat (clutch side): 17 mm · Ø Bearing seat (ignition side): 17 mm · Area of application: Standard · Thread length: 11 mm · Thread length: 15 mm · Dimension needle bearing: 12 / 15 x 14.2 mm (axe 12) · Wide crank webs: 34 mm · Length 1st paragraph: 9 mm · Length 2nd paragraph: 14.5 mm · Length 3rd paragraph: 25 mm · Ø 1st step (on the coupling side): 22 mm · Ø 2nd shoulder (on the clutch side): 17 mm · Ø 3rd step (on the clutch side): 15 mm · Length of shoulder (ignition side): 26.3 mm · Weight: 873 g · Number of gears: 1 pcs
EUR 164.40
swiing® revival 38 mm original cylinder 1.6 PS | Puch
Nominal diameter: 38 mm · Manufacturer: swiing® revival parts · Material: Aluminum · Surface: sandblasted · Displacement: 50 ccm · Crankshaft stroke: 43 mm · Ø cylinder neck: 48 mm · Ø outlet inside: 19 mm · Ø Inlet inside: 9 mm · Thread inlet: M6x1 (standard thread) · Hole spacing inlet: 38 mm · Ø piston pin (B): 12 mm · Outlet type: straight · Hole spacing outlet: 42 mm · Thread outlet: M6x1 (standard thread) · Number of fixing points: 4 pcs · Hole pattern [mm]: 44 x 44 · Decompressor: Yes · Camouflaged: Yes · Area of application: Standard · Alternative version of the Puch OEM number: 349.7.10.105.0
EUR 127.90
Not in stock
Hot 
swiing® revival 38 mm original cylinder Vertex-Edition 1.6 PS | Puch
Manufacturer: swiing® revival parts · Camouflaged: Yes · Material: Aluminum · Surface: sandblasted · Crankshaft stroke: 43 mm · Displacement: 50 ccm · Nominal diameter: 38 mm · Ø cylinder neck: 48 mm · Ø outlet inside: 20 mm · Ø Inlet inside: 9 mm · Hole spacing inlet: 38 mm · Inlet window: 2 · Ø piston pin (B): 12 mm · Hole spacing outlet: 42 mm · Thread inlet: M6x1 (standard thread) · Hole pattern [mm]: 44 x 44 · Area of application: Standard · Number of fixing points: 4 pcs · Outlet type: straight · Thread outlet: M6x1 (standard thread) · Decompressor: Yes
EUR 182.70
Moped fans like you also bought:
Hot
swiing® ingenious exhaust 22 mm camouflaged 2-piece | Puch Maxi S, N
Surface: chrome-plated · Manufacturer: swiing® ingenious parts · Material: Steel · Color: Chrome · Mounting type: Stud bolts & nuts · Mounting type: Welded lug · Ø outside: 59 mm · Total length: 910 mm · Ø Silencer: 54.5 mm · Ø Flame tube outside: 22 mm · Exhaust type: Flute · Number of fixing points: 4 pcs · Flame tube attachment: Flange
EUR 182.70
Dell'Orto 19 mm PHBG CS carburetor hand choke
Manufacturer: Dell'Orto · Material: Aluminum · Camouflaged: No · Component group Carburetor: Carburetor complete · Nominal diameter: 19 mm · Carburetor type: PHBG CS · Total length: 82 mm · Color: black · Width: 70 mm · Ø without reducing sleeve: 26 mm · Ø Inside entrance: 19 mm · Ø Internal connection: 24 mm · Ø Output inside: 19 mm · Ø Air filter connection: 32 mm · Ø Air filter connection: 60 mm · Height: 124 mm · Air filter connection thread: MF32x1.25 (fine pitch thread) · Area of application: Racing · Area of application: Tuning · Ø fuel hose connection: 5.4 mm · Ø fuel hose connection: 6 mm · Mounting type: Plug connection clamped · Mixed oil connection: Yes · Vacuum connection: Yes · Choke control: Hand choke · Choke nozzle size: 60 · Nozzle thread: M5x0.8 (standard thread) · Nozzle size: 75 · Size of secondary nozzle: 45
EUR 146.10
Fuel tap horizontal M12x1 (with union nut) outgoing at the bottom
Possible lever positions: open / closed / reserve · Material lever: Metal · Filter type: Plastic net · Ø fuel hose connection: 6 mm · Installation direction: horizontal / horizontal · Outlet direction: below · Mounting type: Union nut · Spare tube shape: curved · Thread type: MF12x1 (fine pitch thread) · Reserve level: 70 mm
EUR 12.10
swiing nozzle set M3.5 (64 - 74) Bing SRE, SRA, SRC, SRF
Manufacturer: swiing · Material: Brass · Quantity: 6 pcs · Component group Carburetor: Spraying · Carburetor type: SRA (1/11/31) Velux · Carburetor type: SRA (1/11/35) Velux · Carburetor type: SRC · Carburetor type: SRE · Carburetor type: SRF · Drive: Slot · Nozzle type: Main nozzle · Total length: 6 mm · Nozzle thread: M3.5x0.6 (standard thread) · Nozzle size: 64 · Nozzle size: 66 · Nozzle size: 68 · Nozzle size: 70 · Nozzle size: 72 · Nozzle size: 74
EUR 19.40
NTN 6203 C3 Ball bearing 17/40/12
Bearing cage: "-" Sheet steel cage ball-guided · Stock number: 6203 · Width: 12 mm · Inner ring width: 12 mm · Manufacturer: NTN · Ball bearing closed: No · Bearing clearance: C3 · Groove ring: No · Material: Steel · Surface: blank · Bearing type: Deep groove ball bearing · Ø inside: 17 mm · Ø outside: 40 mm · Area of application: Standard
EUR 10.80
Collection only possible with online purchase and appointment.
